DCS PHFS-DWWT Spezifikationen

THE PHOENIX 111 PATIO HEATERUse and Care GuideModels: CE-PHFS-DW-BK-L CE-PHFS-DW-BL-L CE-PHFS-DW-BZ-L CE-PHFS-DW-GN-L CE-PHFS-DW-SS-L CE-PHFS-DW-WT-LD

LP Gas Hook-Up9The heater comes equipped with a regulator/hose assembly for connection to a standard 13kggas tank (not included) and 18” tank strap to

10PRECAUTIONS• Periodically check the whole gas system for leaksor immediately check if the smell of gas is detected.• Extinguish all open flames• Nev

STEP 9 Locate the cap nuts,washers (4 ea.) andreflector shield.Tip the heater backwards andsupport it with stable horizontal surface (i.e.sawhorse, wo

This outdoor heater is primarily for temporaryheating of outdoor patios,decks,spas, pool, andwork areas.This heater is not intended for indoor use ore

L ig hting And S hutdown13BEFORE TURNING THE GAS SUPPLY “ON”Visually inspect the hose assembly for evidence of excessive abrasion, cuts or wear.

Storage And Insect Warning14NOTE: When storing the heater, the connection between the LP cylinder and the heater must be disconnected and the LP cylin

NOTE: Unit must be cold before removalBURNER REMOVAL 1) Remove reflector and emitter assembly by removing the screws that fasten the emitter assembly

P ilot CleaningWhen storing the heater the connectionbetween the LP cylinder and the heater mustbe disconnected and the LP cylinder removedand store

Troub les hooting 17Can you Match light thepilot?PROBLEM: Pilot does not lightusing the piezolighter.YESNOPiezo igniter problem. Is there a spark at

Troub les hooting18Is there adequate gas supply?PROBLEM: Burner flame islow.YESFill LP cylinderNOIs the supply hose bent or kinked?YESStraighten hoseY

1A Message To Our CustomersWe are glad you selected the Phoenix III by DCS. Because this appliance contains features not found on anyother patio heat

Parts List19Dynamic Cooking Systems, Inc.ITEM PART NO. DESCRIPTION1. 15019-07 1/4-20 Acorn Nut2. 15005-10 Split Washer2.b 15005-15 Flat Washer3. 23002

Parts List20ITEM PART NO. DESCRIPTION1. 23121-XX Post Assembly (1)2. 23096-XX Base Assembly (1)3. 23106-XX Door (1)4. 17314 Manual (1)5. 15003-15 1/4-

Part No.17379 Rev.BLitho in USA 08/2001As product improvement is anongoing process at DCS,wereserve the right to changespecifications or design witho

2Tab le O f ContentsSAFETY PRACTICES AND PRECAUTIONS...3FEATURES...

3Safety Practices & Precautions• Read and become familiar with the entire manual.• Do not use in an explosive atmosphere, keep heater away f

4Features• Weatherproof • All High Heat Parts Made Of Stainless Steel• Uniform Heat Pattern • Flame Out Protection Safety Control Valve• Durable Non-S

5As semb ly I ns tructionsNOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility ofthe installer.STEP

6As s emb ly I ns tructionsSTEP 4 Remove the protective endcap at the bottom of the intake pipe.Make certain that the threads remainbare.Locate the

As semb ly I ns tructions7STEP 5Locate the post assembly. Carefully insert theintake pipe through the top of the post assemblybeing careful not to a

As semb ly I ns tructions8STEP 6To join the post assembly with base cabinet you will need to place the base upright on the floor and lift the post a