DCS RDT-366 Installationsanleitung PDF herunterladen (Seite 12)

UNPACKING AND HANDLING

MOVING AND PLACING THE RANGE (cont.)

lectric and gas connections should be made before the

range is slid into the cabinet opening (see pages 14~18). If

installing a full backguard with the range, it should also be

installed before the range is placed in its final position (refer

to pages 8 & 17). For proper performance, the professional

range should be level. To achieve a flush fit of the range to

adjoining countertops, it will be necessary to have level

cabinets (front to back, and left to right across opening of the

range). After checking the countertops for level and before

sliding the range into place, measure the distance from the

floor to the top of the counter work surface in the rear left

and right corners. Adjust the corresponding rear corner of the

range to an equal height of the counter, as the rear leveling

legs are not accessible once the range is pushed into place.

Once the range is in place, the front leg levelers can be

accessed to level the front of the range. Replace the kick

panel and oven doors by reversing the procedure described

previously. It is important that the two screws retaining the

kick panel are secure to prevent accidental access to live

electrical components and wires (fig. 2).

Anti-tip device should be installed (see page 13 for

instructions). The professional range should be transported by

a dolly close to its final location. The range can be tipped

back and supported on the rear legs while the dolly is

removed. The floor under the legs should be protected (wood

strips, carpet, paneling, etc.) before pushing the unit back into

position.

To remove the kick panel:

Removing two screws at the top and pulling forward. The

ange is held t

o the skid by two bolts in the front, behind the

kick panel, (fig. 2) and two L-brackets located on the bottom

flange of the range back (fig. 3). After removing the bolts and

brackets, the range must be lifted and removed from the skid.

Due to the weight, a dolly with soft wheels should be used to

move this unit. The weight must be supported uniformly

acr

oss the bottom (fig. 4).

Left Rear Shipping

Screws

Fig. 3

22"

Leveling Legs

Range Must

be Uniformly

Supported

on Braces

. 4

eft Rear

hipping Screws

Range Must be

Uniformly

Supported on

Braces

Leveling Legs

Kick Panel

Fig. 2

Kick Panel

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Marcas	Mejores modelos
BenQ	98.K2205.E10 98.K1005.E04 Joybee 100 JOYBEE P330	Otras categorias
Belkin	F8Z295 F8E490 TuneTalk F8Z029ea F8Z901	Otras categorias
Blaupunkt	New York 830 PP10 PP20PK GTP 01-MP3	Otras categorias
Bang & Olufsen	BeoSound 6 BeoSound 2 BeoSound 3	Otras categorias
Bones	Milestone 311	Otras categorias
Bluesound	Powernode	Otras categorias
BayCom	OSCAR	Otras categorias
Buffalo	Media Player LT-H90	Otras categorias
Bose	SoundDock Series II	Otras categorias
BoomGear	MP-825BT MP-700	Otras categorias
Blusens	1960-BR-4GB	Otras categorias
Band Shoppe	LONG RANGER IV	Otras categorias
Bellman & Symfon	BE2270	Otras categorias
Blue Raven	MediaMate 7080	Otras categorias
Beko	MP 300 R	Otras categorias
Balance	HE-CLOCK-23	Otras categorias
Blade	takeMS	Otras categorias
Boss	MICRO BR	Otras categorias
BlueMedia	8200 Series	Otras categorias

DCS RDT-366 Installationsanleitung Seite 12

Kommentare zu diesen Handbüchern

Reproductores de mp3 / mp4 manuales

Empezando en B pagina

DCS RDT-366 Installationsanleitung Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Herde DCS RDT-366

Reproductores de mp3 / mp4 manuales

Empezando en B pagina